Cirrus-logic EP73xx Bedienungsanleitung Seite 54
- Seite / 158
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-8 EP7309/11/12 User’s Manual - DS508UM4
Copyright Cirrus Logic, Inc. 2003
Interrupt Controller
4
Interrupt Register Descriptions
Interrupt Status Register 1 (INTSR1)
Address: 0x8000.0240, Read Only
Definition: The interrupt status register is a 32-bit read only register. The
interrupt status register reflects the current state of the first 16
interruptsourceswithintheEP73xx. Each bit issetif the appropriate
interrupt is active. The interrupt assignment is given below.
Bit Descriptions:
RSVD: Unknown during Read.
EXTFIQ: External fast interrupt. This interrupt willbe active if the
nEXTFIQ
input pin is forced low and is mapped to the FIQ input on the
ARM720T processor.
BLINT: Battery low interrupt. This interrupt will be active if no external
supply is present (
nEXTPWR is high) and the battery OKinput pin
BATOK is forced low. This interrupt is de-glitched with a 16 kHz
clock, so it will only generate an interrupt if it is active for longer
than 125 µs. It is mapped to the FIQ input on the ARM720T
processor and is cleared by writing to the BLEOI location. BLINT
is disabled during The Standby State.
WEINT: Tick Watch dog expired interrupt. This interrupt will become
active on a rising edge of the periodic 64 Hz tick interrupt clock if
the tick interrupt is still active (i.e., if a tick interrupt has not been
serviced for a complete tick period). It is mapped to the FIQ input
on the ARM720T processor and the TEOI location.
Note: WEINT and watchdog timer are disabled during the Standby State. The watch
dog timer tick rate is 64 Hz (in 13 MHz and 73.728–18.432 MHz modes).
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RSVD
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SSEOTI UMSINT URXINT1 UTXINT1 TINT RTCMI TC2OI TC1OI EINT3 EINT2 EINT1 CSINT MCINT WEINT BLINT EXTFIQ
- EP73xx User’s Guide 1
- 1Contents 4
- Chapter 5. System Registers 5
- Chapter 6. Processor Support 6
- Chapter 7. SDRAM Controller 6
- Chapter 9. LCD Interface 6
- Appendix A. Boot Code 8
- Contents 9
- List of Figures 10
- List of Tables 12
- Chapter 1 15
- 1Introduction 15
- Overview 15
- Memory Map and Register List 16
- Internal Register Map 17
- Pin Description 20
- External Signal Functions 21
- Output Bi-Directional Pins 24
- Block Diagrams 25
- References 26
- Chapter 2 27
- 2CPU Core 27
- Programming Register List 27
- Programming Examples 28
- CPU Core 29
- Write Buffer 32
- CPU Register Definitions 33
- User FIQ IRQ SVC Undef Abort 34
- CPU Clocks 35
- On-Chip PLL 36
- PLL Register Descriptions 37
- CPU State Control 38
- Idle State 39
- Power Up Sequence 40
- Table 3-1: Timer Registers 43
- Timer Register Descriptions 45
- Chapter 4 47
- 4Interrupt Controller 47
- Interrupt Register List 47
- Interrupt Operation 50
- Interrupt Listing 51
- Operating State 52
- Standby State 53
- Interrupt Controller 54
- End-Of-Interrupt Locations 59
- Chapter 5 61
- 5System Registers 61
- System Register List 62
- MaverickKey 64
- Unique-ID 64
- BUZ output reflects 65
- EXPCLK is 66
- System Registers 68
- 0032-bit 71
- 1016-bit 71
- 11Reserved 71
- CLKSEL (PE[2])input,latched 72
- Chapter 6 75
- 6Processor Support 75
- Internal Boot Mode 76
- External Boot Mode 76
- CS0 and the 77
- Endianess 78
- Endian Byte Addressing 79
- Processor Support 80
- Chapter 7 81
- 7SDRAM Controller 81
- SDRAM Register List 81
- SDRAM Register Descriptions 83
- SDRAM Controller 84
- SRAM/Expansion Bus Controller 89
- Chapter 9 91
- 9LCD Interface 91
- LCD Register List 91
- LCD DMA Controller 93
- Gray Scale 94
- 4 Bits per pixel 95
- 2 Bits per pixel 95
- 1 Bit per pixel 95
- Hardware Interface 96
- Color LCDs 96
- LCD Register Descriptions 97
- (PALMSW) 98
- FBADDR) 99
- LCD Interface 100
- Operational Overview 102
- Keyboard Interface 103
- Chapter 11 105
- 11General Purpose I/O (GPIO) 105
- Introduction 105
- Features 105
- Programming Example 106
- Register Descriptions 106
- Chapter 12 107
- 12PWM Interface 107
- Block Diagram 107
- PWM Register Descriptions 109
- PWM Interface 110
- PD0 / LEDFLSH)tobetoggledata 111
- Register Definitions 112
- Chapter 14 113
- 14JTAG Interface 113
- Boundary Scan 114
- Debug Modes 115
- Debug/ICE Test Mode 116
- Hi-Z (System) Test Mode 116
- JTAG Interface 117
- ADCCLK) 121
- Bit Descriptions: 122
- (SYNCIO[6:0]) 123
- SSI Port 124
- Chapter 16 125
- 16DAI/CODEC/SSI2 125
- DAI/CODEC/SSI2 Register List 126
- DAI Interface 128
- DAI Clock Generation 129
- Master/Slave SSI2 Interface 131
- Read Back of Residual Data 132
- CODEC Sound Interface 134
- DAI Registers 135
- DAI Control Register (DAIR) 136
- Full Bit Descriptions 137
- DAI Data Register 0 (DAIDR0) 138
- DAI Data Register 1 (DAIDR1) 139
- DAI Data Register 2 (DAIDR2) 140
- DAI Status Register (DAISR) 140
- DAI/CODEC/SSI2 141
- SSI2 Registers 144
- CODEC Register 144
- SIR Encoder 150
- UART and SIR Encoder 153
- WRDLEN Word Length 153
- Appendix A 155
- ABoot Code 155
- Boot Code 156
Verwandte Produkte und Handbücher für Hardware Cirrus-logic EP73xx
Hardware Cirrus-logic AN186 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Cirrus-logic AN187 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Cirrus-logic AN269 Bedienungsanleitung
(65 Seiten)
(65 Seiten)
Hardware Cirrus-logic AN253 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Cirrus-logic EV2 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Hardware Cirrus-logic AN361 Bedienungsanleitung
(10 Seiten)
(10 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.173 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern