Cirrus-logic CRD49530-USB Bedienungsanleitung Seite 37
- Seite / 50
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Detailed Schematic Descriptions
CRD49530-USB User’s Manual
DS705RD3 Copyright 2008 Cirrus Logic 5-4
Each output of the CS42448 has an output filter that consists of an AC-coupling cap (3.3 μF), a pull-down
resistor to prevent the output from floating when not connected to a load, a series resistor (470 Ω) to
provide a voltage drop when the muting transistor is enabled, and a mute transistor that will pull the output
low when the mute control signal is enabled. The series resistor is small enough that it does not affect the
signal in normal operation, assuming a load of at least 10 kΩ is connected to the analog output of the
board.
5.2.7 Microphone Preamplifier
Figure 5-7 shows the microphone preamplifier on the CRD49530-USB, which has a 1/8” microphone input
jack to allow direct connection to an encapsulated condenser microphone (ECM). Because the output of
the ECM is so small, a pre-amplifier is needed to boost the signal to a line-level voltage.
These specifications for the amplifier are noted on the schematic page. These parameters should be
considered when choosing the microphone to be connected to the CRD49503-USB. Too large of a signal
on the CS42448 analog input will result in distortion of the sampled signal.
It is important to note that although the amplifier circuit shown is non-inverting (the input to U12-B is the
same polarity as the output from U12-C), the output of an ECM is inherently inverted since it acts as an
open-collector device. Therefore the microphone signal driven to the CS42448 should be considered an
inverted signal for processing purposes.
5.2.8 Power and Connectors
The audio input connectors consist of:
• 6 RCA jacks for analog input
• 2 RCA jacks for coaxial S/PDIF input
• 2 optical jacks for optical S/PDIF input
The audio output connectors consist of:
• 8 RCA jacks for analog output
• 1 optical jack for S/PDIF output
There is one control connector on the board, J11. This 50-pin connector provides pins for the following
functions:
• Serial control interface for configuring the DSP, codec, and S/PDIF RX
• Reset lines for the DSP and other board devices
• Pins to provide power to the CRD USB Master USB control board
• An interface for delivering audio data from the USB board (feature not yet available)
The DC input connector (J25) for the CRD49530 can accept 9 to 12 V
DC, and the power supply should be
capable of supplying at least 1 amp of current.
The 3 voltage regulators on the CRD49530 generate the 1.8V, 3.3V, and 5V necessary for powering all of
the ICs on the board. Note that the 5 V and 3.3 V regulators run directly off the DC input supply connected
to the CRD49530, while the 1.8 V regulator is dependent upon 3.3 V system power (not necessarily the
3.3 V regulator).
The 3 power jumpers (J17, J18, J19) are used to choose between the on-board regulators, and an
external source for 5 V, 3.3 V, and 1.8 V. This is a feature intended only for special applications, so these
jumpers should be left in the ‘REG’ position for normal operation.
- CRD49530-USB 1
- CRD49530-USB User’s Manual 2
- Contents 3
- Chapter 1 6
- Kit Contents and Requirements 6
- 1.2 Requirements 6
- 1.2.2 Software Requirements 7
- 1.2.4 Cabling Requirements 7
- 1.3.1 Audio Inputs 8
- 1.3.2 Audio Outputs 8
- 1.3.3 Control Header 9
- 1.3.6 CS4953xx Audio DSP 9
- 1.3.7 CS8416 S/PDIF RX 10
- 1.3.8 CS42448 Audio Codec 10
- 1.3.9 Memory 10
- CS4953xx CS42448 11
- CS4953xx 12
- 1.4 Other Useful Information 14
- CRD49530-USB User’s Manual 15
- CRD49530 16
- A. CS4953xx DSP, U5 17
- CRD49530--USB User’s Manual 18
- Chapter 3 20
- 3.1.3 Connecting to a PC 23
- Chapter 4 26
- 4.1 Introduction 26
- Pass-through 26
- 4.2.1 System Block 28
- 4.3.1 S/PDIF Audio Input 29
- 4.3.2 Analog Audio Input 30
- 4.3.3 USB (I 30
- S) Audio Input 30
- 4.3.4 DAI Input 31
- 4.4.1 DAO Output of CS4953xx 32
- ) / Memory Usage 33
- Chapter 5 34
- CRD49530-USB Schematics 34
- 5.1 Introduction 34
- 5.2.3 Memory 35
- 5.2.4 S/PDIF Receiver 35
- 5.2.5 Audio CODEC 36
- 5.2.6 Input/Output Filters 36
- 5.2.8 Power and Connectors 37
- Obtaining Schematic Updates 38
- Figure 5-4. S/PDIF Receiver 42
- Figure 5-5. CS42448 CODEC 43
- Figure 5-7. MIC Pre-AMP 45
- Chapter 6 48
- Troubleshooting 48
- 6.1 Troubleshooting Guide 48
- Revision History 49
- Revision History 50
Verwandte Produkte und Handbücher für Hardware Cirrus-logic CRD49530-USB
Hardware Cirrus-logic AN249 Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Hardware Cirrus-logic CS5340 Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Hardware Cirrus-logic CS5341 Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Hardware Cirrus-logic CS5344 Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Hardware Cirrus-logic CS5345 Bedienungsanleitung
(42 Seiten)
(42 Seiten)
Hardware Cirrus-logic CS5351 Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Hardware Cirrus-logic CS5361 Bedienungsanleitung
(23 Seiten)
(23 Seiten)
LOEWE Spheros R 32 HD+ manuales
Manuales del propietario y guías del usuario para Televisores Lcd LOEWE Spheros R 32 HD+.
Ofrecemos 1 manuales en pdf LOEWE Spheros R 32 HD+ para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern